intrinsic layer
英 [ɪnˈtrɪnzɪk ˈleɪə(r)]
美 [ɪnˈtrɪnzɪk ler]
无杂质层
双语例句
- The separated intrinsic layer can have an inwardly sloping sidewall to focus light incident the photodiode for the unit pixel.
该分离的本征层可具有向内的倾斜侧壁以为单位像素聚焦射入光电二级管的光线。 - Moreover, the band gap depends closely on the optimal thickness of intrinsic layer.
另外，禁带宽度对本征层最佳厚度也有一定的依赖关系。 - Microcrystalline silicon thin film solar cells with different crystal volume fraction ( Xc) intrinsic layer were used to perform light soaking experiments under different light sources.
利用改变硅烷浓度（SC）的方法制备了一系列不同晶化率的微晶硅太阳电池，并将电池在红光和白光两种光源下进行光照实验。 - Results: ① SO could be divided into intrinsic muscle and inherited fibers from duodenum. The intrinsic muscle included inner longitudinal layer and outer circular layer.
结果：①SO可分为固有肌和十二指肠延续肌纤维两类，前者有内纵、外环两层； - The subharmonic instability can be found in a wide extent of the frequencies and Reynolds numbers and the growth rates and amplification factors of amplitude are much higher than that of the primary wave. The secondary subharmonic resonance may be an intrinsic transition mechanism of compressible boundary layer.
二次亚谐波在很宽频率和雷诺数范围内不稳定，其增长率和幅值放大因子都远大于初始波，二次亚谐共振是可压缩边界层转捩的内在机制。 - In a range of intrinsic equivalence of MT, "forward modified method" can correctly restore resistivity and thickness for each conducting layer.
在MT固有的等值性范围内，正演修正法能正确恢复各电性层的电阻率和厚度。 - Study on The Composite and Intrinsic Hardness of Adhesive Layer
粘涂层的复合硬度与本征硬度的研究 - Based on the solution to the intrinsic equation of quantum well energy level, In content of the InGaAs quantum well layer was optimized;
在量子阱能级本征值方程的数值求解基础上，优化了InGaAs阱层材料的In组份含量； - High Conductivity Intrinsic Nanocrystalline Silicon Film and as Buffer Layer in Thin Film Solar Cells
高电导本征纳米硅膜及其缓冲层太阳能电池 - Macrophage staining was found at the intrinsic layer under mucosa membrane, TGF β 1 staining at the granulation tissue, fibroblasts and endothelial cells of blood vessels.
MΦ主要表达于粘膜固有层；TGFβ1主要表达于肉芽组织、成纤维细胞、MΦ及血管内皮细胞。 - High Mobility GaAs Intrinsic Epitaxial Layer Grown by MOCVD
高迁移率GaAs本征外延层的MOCVD生长 - The intrinsic circuit model of ferroelectric liquid crystal ( FLC) is extended into optically addressed spatial light modulator ( OASLM), which take FLC as light modulation layer and a-Si: H as photosensitive layer. Thus a macro model of FLC-OASLM is presented.
将铁电液晶（FLC）的本征电路模型扩展到以FLC为调制层，aSi∶H为光敏层的光寻址空间光调制器（OASLM），建立了FLCOASLM的宏模型。 - Using this intrinsic microcrystalline silicon film as absorber layer in single-junction solar cell, a conversion efficiency of 4.8% was obtained.
把这种高速生长的微晶硅材料用作太阳电池的本征吸收层，在没有优化工艺参数和没有采用ZnO增反电极时，电池的转换效率达到4.8%。 - When the nanograin size of the intrinsic nc-Si: H layer increases, the optical absorption coefficient decreases, resulting in worse performance.
随着本征nc-Si：H层晶粒尺寸增大，本征层的光吸收系数减小，进而导致电池性能下降。 - Because of the defects of hydrogenated intrinsic amorphous silicon layer, this phenomenon appeared. In order to eliminate the defects, heighten the lifetime of minority carriers and improve the performance of HIT solar cells, process of annealing was studied.
这一现象可能是由本征氢化非晶硅层的缺陷所致，所以，接下来本文运用退火工艺，旨在消除这些缺陷，提高制绒硅片的少子寿命，改善HIT太阳电池的性能。 - In this paper, we shall discuss the effects of the band gap, the thickness of intrinsic layer and the back surface field on performance of nc-Si/ c-Si HIT ( Heterojunction with an Intrinsic Thin layer) solar cell.
本论文分析了影响p+（nc-Si）/i（a-Si）/n（c-Si）异质结太阳电池性能的主要因素，包括纳米硅薄膜的禁带宽度、掺杂浓度、本征层厚度以及背电场。 - In addition, the cell performance could be further optimized by improving the quality of materials and selecting the appropriate mobility band gap in intrinsic absorption layer.
此外，提高本征吸收层的材料质量，降低缺陷浓度，选择合适的迁移率带隙也可以使得电池性能得到优化。 - HIT ( Heterojunction with Intrinsic Thin Layer) solar cell has advantages of high efficiency, stability and low costs. It combines low-temperature deposition process of amorphous silicon films with high mobility of crystal silicon and quickly seizes the international PV market.
HIT（HeterojunctionwithIntrinsicThinLayer）太阳电池具有高效、稳定和低价等优点，它结合了非晶硅薄膜的低温沉积工艺和晶体硅的高迁移率优势，迅速抢占了国际光伏市场。 - However, hot-dip aluminizing also has some intrinsic limitations and disadvantages, for instance, there are often pinhole and leakage of hot-dip aluminizing decreasing erosion resisting performance of plating layer in aluminum plating process.
然而，热浸镀铝存在一些固有的局限性和缺点，在镀铝的过程中经常会产生一些针孔漏镀等现象，使得镀层的耐蚀性能下降。